Mart Cyclone 30 Series Скачать руководство пользователя страница 100

Страница: 100 / 322

Basic Operations

3 - 1

Standard Turntable Power Washer v. 4.0

The MART Corporation

3 Basic Operations

Purpose

This chapter provides step-by-step instructions on how to load and wash parts. Read it
before you operate the washer for the first time.

Prerequisites

Before you read this chapter or operate the washer for the first time, we recommend
that you read the following thoroughly:

"Important Safety Instructions and Warnings"

(in the front material)

Chapter 1,

"Overview"

This chapter,

"Basic Operations,"

assumes that appropriate

operating parameters have been established for your washer.
Refer to chapter

"Advanced Operations: Process-Control"

for

information on establishing process-control parameters.

Safety/Precautions

Before you operate the washer, read and follow these recommended safety/precaution
instructions:

WARNING! NEVER get inside the washer cabinet when the
main power supply is ON. This could result in severe injury or
death.

Содержание Cyclone 30 Series



































































































































































































































































































































Результаты поиска

Содержание Cyclone 30 Series

Отзывы:

Mart Cyclone 30 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 100 / 322

Результаты поиска

Содержание Cyclone 30 Series

Отзывы: