Lufft 8511.EAK Скачать руководство пользователя страница 110

Страница: 110 / 158

Manual

LCom

Page 110 of 158

Alarm 2:

Is set if FREEZE-TEMPERATURE is rising AND

FREEZE-TEMPERATURE is greater or equal to (ROAD-TEMPERATURE

– 2.0)

i.e. if the freeze temperature is

rising (over “Freeze Temp Rising Min.” minutes) and 2

(or less) ° below the road temperature

Alarm 3 Freeze Temperature

– black ice

Is set if FREEZE-TEMPERATURE is rising AND ((ROAD-TEMPERATURE

–

FREEZE-TEMPERATURE) < 0.2)

i.e. if the freeze temperature is

rising (over “Freeze Temp Rising Min.” minutes) and

0.2 (or less) ° below the road temperature

Alarm 3 Dewpoint

– slippery frost

Is set, if (SALINE-CONCENTRATION = 0) AND (ROAD-TEMPERATURE < 0) AND

(AIR-TEMPERATURE > (ROAD-TEMPE2)) AND (DEWPOINT > -4), i.e. if

there is no residual salt, and road temperature is below 0 °C and air temperature is at

least 2 °C above road temperature, and dewpoint is above -4 °C

Alarm 3 Precipitation

– freezing rain

Is set, if (PRECIPITATION-

TYPE = “Rain”) for at least “Const. Rain Min.” minutes,

and (ROAD-

TEMPERATURE < 0), i.e. precipitation type is “Rain” for at least the

“Const. Rain Min.” (default 10) minutes, and road temperature is below 0°C.

Alarm 3 Precipitation

– snow

Is set, if (PRECIPITATION-

TYPE = “Snow”) for at least “Const. Snow Min.” minutes,

and (ROAD-

TEMPERATURE < 0.2), i.e. precipitation type is “Snow” for at least the

“Const. Snow Min.” (default 15) minutes, and road temperature is below 0.2 °C.

5.13.4 Prognosis Road Condition

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды