Lufft 8511.EAK Скачать руководство пользователя страница 8

Страница: 8 / 158

Hardware Description

LCom Connector

3.1 Power Supply

LCom is powered via UB+/GND (CON220-1) on the UMB-EAK. The allowed voltage

range is 10VDC to 28VDC. The input is protected against reverse polarity, surge and

burst.

Power supply for the GPRS modem (GUB_2/GND) and Party-Line modem

(GUB_3/GND) are provided on connector CON220-1. Depending on the status of the

modem, LCom can switch these two voltages on and off to reset the respective

modem.

The power supply for the UMB network (GUB1/GND) is available on CON220-1. The

maximum output current is 4 amp. If higher currents are required, the sensor heater

tapes must be powered and protected separately.

All output voltages are short-cut proof.

3.2 Operation

The standard functions of the LCom can conveniently be used via the touch screen

display. For configuration purposes we recommend the connection of a PC keyboard

with USB connection, or connecting a PC/Laptop via LAN and using the service

program.

RESET

USB

Ethernet

CON220-1/Pin1

CON220-2/Pin1

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды