Lufft 8511.EAK Скачать руководство пользователя страница 113

Страница: 113 / 158

Manual

LCom

Page 113 of 158

•

Simulation Active:

The simulation model for saline concentration and freeze

temperature is activated

•

Values TLS coded:

the input values (waterfilm) are TLS coded. Note that this

does not affect the coding of the output values

– i.e. the freeze temperature is

always reported as °C and may need to be scaled (for transmission via TLS).

•

Number of Instances:

the number of model calculation instances

•

Instance #:

select the instance to be configured via this combo box

Instance Parameter:

•

Saline Concentration Sensor:

the sensor channel for saline concentration

(road sensor output)

•

Waterfilm Sensor:

the sensor channel for water film height (road sensor

output)

•

RS Factor:

multiplication factor for raw salinity value

•

Waterfilm Limit:

minimal water film for measured salinity

•

Dry Decrease Factor:

reduction divisor (dry road)

•

Decrease Time:

time constant for reduction on wet road

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды