Lufft 8511.EAK Скачать руководство пользователя страница 116

Страница: 116 / 158

Manual

LCom

Page 116 of 158

Multiple instances for the model calculation can be configured (in case the station is

equipped with more than one road sensor).

Note: the default values are preset for the (German) TLS protocol, e.g. the “Dewpoint

diff” value of 5.0 refers to 0.5 °C as the temperatures for TLS are in 1/10 °C.

Please adjust the parameters as needed for the sensor channels configured here.

•

Active: this instance of the model calculation is active

•

Dewpoint Diff: the value that the road temperature must be below the dew

point temperature for “slippery frosty” to be set (see above)

•

Road Condition Dry: the road condition code for “dry”

•

Slippery Frosty: the road condition code for “slippery frosty”

•

Road Condition: the road condition sensor channel

•

Road Temperature: the road temperature sensor channel

•

Water Film: the water film sensor channel

•

Dew point: the dew point sensor cannel

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды