Lufft 8511.EAK Скачать руководство пользователя страница 92

Страница: 92 / 158

Manual

LCom

Page 92 of 158

5.11 GPRS / Analog Modem

The parameters for the GPRS connection or the Hayes-Compatible analog modem

are configured here.

5.11.1 GPRS Modem

he “PIN” for the SIM card (unless switched off) and the access data (user

name/password/server) for the GPRS provider need to be configured here.

After changing the GPRS configuration data the system may have to be rebooted

(some parameters are stored in the registry) in order for the changes to take effect.

Note: The RS232 interface on the GPRS modem must be set to 115200 8 N 1

and hardware handshake must be enabled.

If “Upload IP” is selected, and “AutoUpdate” is active (see below), the current IP

address is stored in a text file and transmitted to the AutoUpdate server after the

connection has been established.

If “GPRS Modem Active” is not active, the GPRS modem parameters can be

set/changed, and the

connection can be initiated manually via “Connect”.

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды