Lufft 8511.EAK Скачать руководство пользователя страница 121

Страница: 121 / 158

Manual

LCom

Page 121 of 158

(depending on the configured input channels) calculates a simulated (“expected”)

value for the water film from precipitation intensity, air temperature and humidity.

The parameters are as follows:

•

Waterfilm:

the waterfilm as measured by the road sensor (in mm)

•

Scale:

a scale factor to convert the waterfilm to mm if the input channel does

not report the waterfilm in mm (e.g. a TLS coded input channel)

•

Precip. Intensity:

the precipitation intensity (in mm/h)

•

Scale:

a scale factor to convert the precipitation intensity to mm/h if the input

channel does not report the precipitation intensity in mm (e.g. a TLS coded

input channel).

•

Air Temperature:

the air temperature (in °C)

•

Scale:

a scale factor to convert the air temperature to °C if the input channel

does not report the air temperature in °C (e.g. a TLS coded input channel)

•

Rel. Humidity:

relative humidity (in %)

•

Waterfilm Time Factor:

a time factor used in calculating the smoothed water

film height

•

Waterfilm Decrease Delay:

a decrease delay used in calculating the

smoothed water film height

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды