Lufft 8511.EAK Скачать руководство пользователя страница 52

Страница: 52 / 158

this subtree contains entries for different Lufft road sensors (Non-Invasive Road Sensor (NIRS), passive road sensor

(IRS31/IRS31Pro), active road sensors (ARS31)) and allows to report all UMB sensor channels of the respective UMB sensor type in

the iso.org.dod.internet.private.enterprises.nema.nemaPrivate.informatikWerkstatt.sensorData.roadSensors

.1.3.6.1.4.1.1206.3.50.1.1 subtree

roadSensors.numNonInvasiveRoadSensors.0

.1.3.6.1.4.1.1206.3.50.1.1.1.0

Configurable

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsRoadSensorIndex.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.1.x

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nisrSensorHeight.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.2.x

Configurable

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsSensorLocation.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.3.x

Configurable

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsRoadSurfaceTemperature.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.4.x

NIRS-UMB Channel 100
(transmitted in 1/10 °C, scale
factor 10)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsFreezingTemperature.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.5.x

NIRS UMB Channel 110
(transmitted in 1/10 °C, scale
factor 10)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsWaterFilmHeight.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.6.x

NIRS UMB Channel 600 (in
µm)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsIceLayerThickness.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.7.x

NIRS UMB Channel 601 (in
µm)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsRoadCondition.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.8.x

NIRS UMB Channel 900
(Lufft coded)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsIcePercentage.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.9.x

NIRS UMB Channel 800
(in %)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsSalineConcentration.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.10.x

NIRS UMB Channel 810
(in %)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsSnowHeight.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.11.x

NIRS UMB Channel 610 (in
mm)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsFriction.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.12.x

NIRS UMB Channel 820
(transmitted in 1/1000, scale
factor 1000)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsRoadWeatherIndex.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.13.x

NIRS UMB Channel 910 (0,1,
or 2)

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsServiceLevel.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.14.x

NIRS UMB Channel 4000

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsRemainingTimeToNextService.x .1.3.6.1.4.1.1206.3.50.1.1.2.1.15.x

NIRS UMB Channel 4001

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsLampStatus.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.16.x

NIRS UMB Channel 4002

roadSensors.nonInvasiveRoadSensorTable.nonInvasiveRoadSensorEntry.nirsMeasureStatus.x

.1.3.6.1.4.1.1206.3.50.1.1.2.1.17.x

NIRS UMB Channel 4003

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды