Lufft 8511.EAK Скачать руководство пользователя страница 119

Страница: 119 / 158

Manual

LCom

Page 119 of 158

•

Road Condition:

the road condition sensor channel

•

Precipitation Type:

the precipitation type sensor channel

•

Friction:

the friction sensor channel

•

Air Temp. Threshold:

the air temperature threshold value (default 0)

•

Road Temp

. Threshold: the road temperature threshold value (default 0)

•

Road Condition Encoding:

encoding/type of the road condition sensor

channel

•

Precipitation Type Encoding:

encoding/type of the precipitation sensor

channel

•

Friction threshold:

the friction threshold (default 0.4)

A result value of 0 indicates no alarm condition, i.e. the beacon should be switched

off

A result value greater than 0 indicates an alarm condition, i.e. the beacon should be

switched on. The different alarm values (1…5) indicate which of the alarm conditions

shown in the following flow chart was met.

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды