Lufft 8511.EAK Скачать руководство пользователя страница 137

Страница: 137 / 158

Manual

LCom

Page 137 of 158

<set-ntcip-snmp-dll>

dll-filename

Sets the name of the SNMP

agent for NTCIP (dll) in the

registry (for updating the

SNMP agent to a new version)

Device address, monitor command

Sends the “monitor” command

to the specified device.

Command and response are

written to a file

(MonitorCmd<timstamp>.txt)

which is transferred to the

update server.

<get-umb-eeprom>

Device address,

start address,

AT|DOUBLE

Reads the corresponding

value from the EEProm of the

UMB device. If successful, the

result is written to a file and

transferred to the server.

<set-umb-eeprom>

Device address,

start address,

AT|DOUBLE,

new value

Sets the corresponding value

in the EEProm of the UMB

device. The result (successful

or not) is written to a file and

transferred to the server.

<pin-set-umb-eeprom>

Device address,

start address,

AT|DOUBLE,

new value

[,pin]

Sets the corresponding value

in the EEProm with PIN

protection. The result is written

to a file and transferred to the

server. The default pin is used

if no pin is specified.

<RESET-TLS-

CHANNEL-INACT>

Re-sets TLS channel

assignment for all channels

that are “inactive” to 0 (so

channel is not “tls configured

but passive” anymore)

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды