manualshive.com logo in svg

Lufft 8511.EAK, Руководство по эксплуатации

Поделиться
Скачать
Lufft 8511.EAK Скачать руководство пользователя страница 18

5.4  Status Display 

This dialog is displayed as the default. The status of the active sensors, including the 

most recent measurements, is displayed together with the general system status 

(UMB and Uplink communication). 

 

 

 

If a sensor value is converted by scaling or value mapping (see below), the 

calculated value and the original value (in brackets) are shown. 

 

If a range violation for a TLS data type is detected for a value, the value is highlighted 

in red (the corresponding DE error status is then reported for the sensor). 

 

 

If the UMB device reports an error value for a sensor channel, the UMB error code is 

displayed 

in the “Value” column, highlighted in red. If an UMB device does not report 

a value for a sensor channel at all (e.g. because the device does not respond) the 

complete sensor data line is highlighted in red. 

Содержание 8511.EAK































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды