manualshive.com logo in svg

Lufft 8511.EAK, Руководство по эксплуатации

Поделиться
Скачать
Lufft 8511.EAK Скачать руководство пользователя страница 11

3.5  UMB Connection 

 

The data connection and power supply are provided over the UMB connection. 

Please note that the maximum current on the LCom

’s power supply output is 4 amp. 

If higher currents are required, the sensor heater must be powered and protected 

separately. 

Interface settings: 19200 baud, 8 data bits, no parity, and 1 stop bit. 

 

LCom 

Connection 

UMB Connection  

(internal bus) 

A (CON220-1/Pin 5) 

-------------------------------- 

A1 

B (CON220-1/Pin 6) 

-------------------------------- 

B1 

 

 

 

GUB_1 (CON220-1/Pin 3) 

-------------------------------- 

UB+ - 1V 

GND (CON220-1/Pin 4) 

-------------------------------- 

GND 

LCom/internal UMB bus wiring. 

 

3.6  Ethernet 

10/100 Mbit with TCP/IP stack 

IP address: 192.168.0.50 

Net mask: 255.255.255.0 

Standard gateway: - 

All settings can be changed in Windows CE control panel 

 

3.7  USB 

A USB hub, keyboard, mouse and memory stick can be connected to the USB 

interface. 

 

Содержание 8511.EAK































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды