Lufft 8511.EAK Скачать руководство пользователя страница 115

Страница: 115 / 158

Manual

LCom

Page 115 of 158

•

Encoding:

encoding of precipitation type (Lufft-UMB, Lufft Frequency or

TLS/WMO

•

Precipitation Diff:

sensor channel for precipitation difference (mm)

•

Air Temperature:

sensor channel for air temperature

•

TLS coded:

temperatures (air and dewpoint) are TLS coded (-> in 1/10 °C)

•

Dewpoint / Rel. Hum:

sensor channel for dewpoint or relative humidity

•

Is Dewpoint:

if selected, the sensor channel “Dewpoint / Rel. Hum” is treated

as a dewpoint sensor channel. If not, a relative humidity channel is assumed

an the dewpoint value is calculated internally from relative humidity and air

temperature.

5.13.8 Slippery Frosty

Here the parameters for the model calculation “Slippery Frosty” can be configured.

This model calculation extends the road condition by a “slippery frosty” condition. The

calculation follows following rule:

Road condition is “dry”

AND water film is 0

AND road temperature is below 0

AND (road temperature plus dewpoint diff) is below dewpoint

THEN road condition is set to “slippery frosty”

OTHERWISE road condition is left unchanged

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды