Lufft 8511.EAK Скачать руководство пользователя страница 80

Страница: 80 / 158

Manual

LCom

Page 80 of 158

5.9.1 MSSI Configuration

The following parameters can be set for MSSI protocol:

•

Soap Reset Timeout:

if no Soap/MSSI Request is received within the

configured time interval, the Soap/MSSI protocol stack is reset. This is to

handle a known problem that the MSSI protocol stack may “hang” sometimes

(under unknown circumstances).

•

Check MSSI activity:

if this option is selected, the MSSI requests are

monitored, and if the configured time intervals for Modem Reset Timeout or

LCom Reboot Timeout is expired without MSSI activity, the appropriate action

is taken.

Modem Reset Timeout:

if there was no MSSI activity/request for the

configured time interval (in seconds), the GPRS or Analog modem is

reset (if either is configured/active). A timeout value of 0 will disable the

modem reset.

LCom Reboot Timeout:

if there was no MSSI activity/request for the

configured time interval (in seconds), the LCom will be rebooted. A

timeout value of 0 will disable rebooting.

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды