LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 99 / 218

3 - 29

(5) Four wheel drive lever (4WD)



This lever is used to engage/disengage the four
wheel drive (4WD).



Before operating the 4WD lever, press down the
clutch pedal, brake pedals, and stop the tractor
completely.



Push the 4WD lever upward for engaging 4WD.



4WD is very effective in the following cases.

- When increasing the towing power for heavy
work.
- In case of working in sandy soil.
- To prevent tractor from spinning in wet land.

Four wheel
drive lever

4WD

2WD

(6) Middle PTO lever (if fitted)



This lever is used to engage/disengage the
middle PTO gear (optional).



Before operating the middle PTO lever, place
the PTO switch in “OFF” position and wait until
the shaft is stopped completely.



Pull the middle PTO lever upward to engage the
middle PTO gear.



For further information of the middle PTO shaft,

see chapter 4-5-(2) in this manual.

Middle PTO lever

▶

When driving on public road, disengage the 4WD. If not, it may cause damage of

transmission drive line and serious accident. After working in the field, select the
2WD.

▶

While driving the tractor at high speed with the 4WD engaged, sharp steering may

cause an accident.

Caution

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды