LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 97 / 218

background image

3 - 27

(1) Main gear shift lever

(Mechanical)



Four speed gear shift and neutral position is
available.



The main gear shift lever can be operated while
driving after depressing clutch pedal. It is not
necessary to stop the tractor completely due to
the synchromesh gears.

Notice

▶

Operate the main gear shift

lever by correct “

H”

pattern. If

operated diagonally, it may
cause a failure.

Main gear
shift lever

Differential
lock pedal

(2) Differential lock pedal



When the rear wheel is slipping and the tractor

can not move forward, stop the tractor and press
down the differential lock pedal.



The differential lock is effective for working on

the slippery ground.



If engaged, both rear wheels will rotate at equal

speed. So, It can disturb the steering operation.



Take your foot off the pedal to release the
differential lock. If the differential force is
reduced to some extend, the lock is released
automatically.



If the differential lock does not disengaged (i.e.
the turning radius is larger than normal condition
and the turning is not smooth), depress the
clutch pedal and/or press the left/right one-side
brake pedal slightly for a second each other.



This pedal is installed on the step floor, but the
location is;
- on the right-hand side for mechanical model
- on the left-hand side for HST model.

Mechanical

Differential
lock pedal

HST

▶

Do not turn the tractor with pressing the differential lock pedal.

▶

Do not use this differential lock pedal while driving on public road.

▶

Do not engage the differential lock when one wheel is spinning.

Warning

Mechanical

4

2

3

1

«
...
95
96
97
98
99
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: Mahindra Страницы: 368

Бренд: Ford Страницы: 41

Бренд: Stockman Страницы: 6

Бренд: KitchenAid Страницы: 7

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 3

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 1

Бренд: Komatsu Страницы: 6

Бренд: Komatsu Страницы: 6

Бренд: Komatsu Страницы: 6

Бренд: Broan Страницы: 32

Бренд: SpeedEPart Страницы: 28

Бренд: Hagie Страницы: 120

Бренд: WALTERSCHEID Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды