LS tractor MT230E 2020 Скачать руководство пользователя страница 63

Страница: 63 / 218

2 - 3

(2) Driver’s seat



At the lower end of the seat, there is a switch to

detect that operator is sitting in the driver’s seat.



If the operator gets up from the seat while

engine is running

, the engine will stop

automatically for safety in case of ;

①

getting up from the seat for more than 2

seconds with HST pedal NOT in neutral position.

②

the HST pedal is in NEUTRAL and rear PTO is

engaged without applying parking brake.

③

the Middle PTO lever (optional) is engaged.



Before leaving the driver’s seat,

- turn the PTO switch to the “OFF” position.
- place the middle PTO lever (optional) in the
“OFF” position.
- apply the parking brake.

Seat switch

warning

▶

Do not arbitrarily remove the seat switch. When replacing the seat, make sure to

check if the seat switch is correctly in place. If not, the engine can not be started.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Бренды по названию

Популярные бренды