LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 17 / 218

1 - 3

(1) Before using the tractor

※

Must read and understand this operator’s manual carefully and

always refer to information and prescriptions outlined in this manual
to prevent all potential health and safety risks.

◆

General information for intended use



Your tractor is designed and manufactured to pull, to carry, to supply the power a variety of mounted

or towed equipment

for agriculture

. Do not use the product for other purposes than intended by the

manufacturer and outlined in this manual. Do not use this tractor for light/heavy forestry applications.



Do not use the product beyond its

limits of terrain gradient

and stability than outlined in this manual.

Using the tractor beyond these limits may cause a overturning accident.



Do not use the tractor on higher speeds than allowed by the load of the tractor and road condition.

Always choose

a suitable driving speed

to maintain the stability of the tractor.



Do not use the tractor

near or on soft verges

of canals and brooks or banks and verges that are

undermined by rodents. The tractor may sink sideways and roll-over.



Do not use the tractor on brittle bridge heads and poor bridge floors. These constructions may

collapse and cause overturning of the tractor.

Always check out the condition and carrying

capacity of bridges and ramps

prior to engage.



Do not use the tractor without wearing the seat belt and Roll-Over Protective Structure (ROPS)

during operations where roll-over or tip-over hazards exist. The ROPS will only be fully effective when
the driver remains attached to his/her seat.



Do not use equipment mounted on the tractor which is not

correctly matching and firmly fixed

Such equipment may increase the risk for roll-over and hit the tractor when coming loose.



Do not use the tractor in combination with equipment arbitrary, without

having consulted the

specific operator’s manual provided with the equipment

. This manual alone cannot provide you

with all the information about safety operation of the combination.



Do not use the tractor beyond its

limits of dynamic stability

. High speed, abrupt maneuvers, and

fast and short cornering will increase the risk of roll-over.



Do not use the tractor for

overloaded pulling work

, in cases where you don’t know if the load will

yield, for instance when pulling stumps. The tractor may flip over when the stump is not yielding.



Be extremely cautious when working with the tractor

on forage silos without lateral concrete

walls

. A wide track setting may improve the lateral stability of the tractor.



Be cautious that the

center of gravity of the tractor may increase

when the front-end loader is

loaded or the three-point linkage are raised. In these conditions, the tractor may roll-over earlier than
expected.



Do not step down from the tractor without shutting down the PTO, shifting the transmission

to neutral and applying the parking brake.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды