LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 156 / 218

background image

5 - 8

Fatty Acid Methyl Ester Biodiesel (Biodiesel Fuel) consists of a family of fuels derived from
vegetable oils treated with methyl esters.

NOTICE: Biodiesel Fuel blends are approved for your engine only if they comply with EN14214

Specification Standards or ASTM D6751.

NOTICE: It is imperative that you check which blend is approved for your engine with your

authorized local dealer. Be aware that the use of Biodiesel Fuel that does not comply with the

Standards mentioned above could lead to severe damage to the engine and fuel system of your

tractor. The use of fuels that are not approved may void manufacturer warranty coverage.

Biodiesel approved blend

The use of biodiesel blends meeting Specification Standards ASTM 6751 or EN14214 are
approved for your engine

up to B7 (7% blend ratio)

. It is highly recommended to use biodiesel

fuel from accredited suppliers to maintain quality and consistency of the fuel.

(4) Biodiesel fuel

Biodiesel Fuel Usage Conditions

NOTICE: The Biodiesel Fuel must meet the fuel Specification mentioned above.

Biodiesel Fuel must be purchased from a trusted supplier that understands the product and
maintains good fuel quality. Biodiesel Fuel must be pre-blended by the supplier. Mixing Biodiesel
Fuels on-site can result incorrect mixture that can lead to problems with both engine and fuel
system.

Engine performance is affected by the use of Biodiesel Fuel. There may be up to

12%

reduction in

power or torque depending on the blend used.

NOTICE: DO NOT modify the engine and/or injection pump settings to recover the reduced

performance.

The reduced power must be accepted if using any Biodiesel Fuel blend.

Some modification may be required to allow your engine to run Biodiesel Fuel. Consult your dealer
for complete information on these modifications.

Biodiesel Fuel has a higher cloud point than Diesel Fuel.

NOTICE: The use of high Biodiesel Fuel blends are not recommended in cold weather conditions.

With Biodiesel Fuels, it may be necessary to change the engine oil, engine oil filter and fuel filter
elements more frequently than with Diesel Fuels. For maintenance interval of the fuel filter, refer to
the following table.

Biodiesel Fuel

Maintenance Interval of the fuel filter

≤ BD 7

500 hours

≤ BD 12

400 hours

≤ BD 20

250 hours

«
...
154
155
156
157
158
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Broadmoor 2600 Series

Бренд: Simplicity Страницы: 40

19B70054 Series

Бренд: Cub Cadet Страницы: 32

Бренд: wsm Страницы: 303

Бренд: wsm Страницы: 619

Бренд: GOLDONI Страницы: 43

Бренд: Walker Страницы: 28

COMPAX CL Series

Бренд: Zetor Страницы: 114

Бренд: AUSA Страницы: 32

Cropmaster VAK1 Series

Бренд: David Brown Страницы: 51

Бренд: Snapper Страницы: 4

Бренд: Spearhead Страницы: 54

TWIGA CLASSIC S51

Бренд: Spearhead Страницы: 54

Бренд: Spearhead Страницы: 76

Бренд: SUMMIT EQUIPMENT Страницы: 30

Бренд: SUMMIT EQUIPMENT Страницы: 35

Бренд: RHINO Страницы: 3

KUBOTA GRAND-L30 Series

Бренд: RHINO Страницы: 4

Бренд: GGP Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды