LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 95 / 218

background image

3 - 25

(19) Cruise control lever (HST

Type)



For cruise drive, push down the cruise control

lever with pressing the HST forward pedal. And
then, the HST pedal will be fixed at that position
and the driving speed of the tractor will be
maintained constantly.



To exit the cruise control drive;

1) Press the brake pedal down or
2) Press the HST pedal forward little more.

And then, the HST pedal returns to the neutral
position and the cruise drive will be stopped.

▶

During the cruise drive, DO NOT press the HST reverse pedal to release the

cruise drive or to reverse the tractor. After stopping the cruise drive as above
described, use the HST reverse pedal.

▶

DO NOT try to raise up the cruise control lever in order to quit the cruise control

drive. It may cause a failure of the cruise control linkage system.

warning

Cruise control lever

Cruise drive

Release

HST forward
pedal

(18) HST forward/reverse pedal

(HST type)



Press down the HST forward pedal slowly in
order to move the tractor forward and if releasing
the pedal, it returns back to the neutral position,
and the tractor stops.



The HST reverse pedal is operated in the same
way as the HST forward pedal.

HST

reverse

pedal

HST

forward

pedal

warning

▶

When releasing the HST pedal while driving in high speed, the braking distance

can be extended depending on the load conditions. At this time, press down the
brake pedal(s) to stop the tractor.

▶

DO NOT operate the HST pedal hastily. It may cause a shock to you.

«
...
93
94
95
96
97
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: GE Страницы: 24

Бренд: Ariens Страницы: 44

Бренд: KitchenAid Страницы: 7

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 3

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 1

Бренд: Wallenstein Страницы: 36

106 41 forterra turbo

Бренд: Zetor Страницы: 257

Бренд: Mahindra Страницы: 87

T2 Versu Series

Бренд: Valtra Страницы: 36

Бренд: Webb Страницы: 44

Zero Turn 73997

Бренд: Classic Accessories Страницы: 3

Бренд: Premier Страницы: 14

Бренд: BCS Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды