LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 188 / 218

background image

5 - 40

5-11. Every 1000hr or 1-year check

(2) Checking Nozzle injection pressure



Contact your authorized local dealer for check.

Normal injection pressure (Common rail): 180MPa (26100 psi)

▶

Only qualified service personnel should perform this maintenance. Contact your

authorized local dealer for this maintenance. Operation of engines with incorrect
valve lash can reduce engine efficiency, and also reduce engine component life.

Caution

▶

Ensure that the engine can not be started while this maintenance is being

performed. To help prevent possible injury, do not use the starting motor to turn the
flywheel.

▶

Hot engine components can cause burns. Allow additional time for the engine to

cool before measuring/adjusting valve lash clearance.

Warning

▶

Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel

system component that will be disconnected. Fit a suitable cover over disconnected
fuel system component.

▶

If a fuel injector is suspected of operating outside of normal parameters, it should

be removed by a qualified technician. The suspect fuel injector should be taken to
an authorized agent for inspection.

Caution

▶

Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire.

▶

Work carefully around an engine that is running. Engine parts that are hot, or parts

that are moving, can cause personal injury.

▶

Make sure that you wear eye protection at all times during testing. When fuel

injection nozzles are tested, the high pressure test fluid can pierce the skin and
cause serious injury to the operator. Always keep the tip of the fuel injection nozzle
pointed away from the operator and into the fuel collector and extension.

Warning

(1) Adjusting Engine valve clearance

Valve clearance



Contact your authorized dealer to check the

valve clearance.

Normal: 0.25mm (0.0098 in)

If the gap is large, the valves can make a loud
tapping noise and if the gap is too small, the
engine output power may be reduced due to
leakage of compressed air.

«
...
186
187
188
189
190
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: KitchenAid Страницы: 7

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 19

Бренд: KitchenAid Страницы: 3

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 1

Бренд: Ventrac Страницы: 69

Бренд: Ventrac Страницы: 72

Бренд: TCP Страницы: 82

Бренд: FENDT Страницы: 6

TeeJet Matrix Pro 570G

Бренд: Spraying Systems Страницы: 127

GE PROFILETM GCG1500L

Бренд: GE Страницы: 2

Бренд: Worksaver Страницы: 36

Бренд: Worksaver Страницы: 42

Бренд: Trac Vac Страницы: 9

Бренд: TYM Страницы: 249

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды