LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 88 / 218

3 - 18

⑥

Inhibited regeneration mode

NOTICE : Only use this mode when regeneration

needs to be delayed or stopped because of an

operation condition that may risk a fire hazard due

to high exhaust temperatures during regeneration.

NOTE : Even if the DPF regeneration indicator(1)

is ON during the regeneration process, the

inhibited regeneration mode can be set.

The regeneration mode can be delayed or
stopped by the use of the DPF switch(3) that is
located on the left-hand side of the dash.

To set the inhibited regeneration mode :

1. Press down the lower side(B) of the DPF

switch(3). And then DPF inhibited regeneration
indicator(2) will be turned on.

NOTICE : When tractor arrives at a safe

regeneration location, press again the lower

side(B) of the DPF switch to exit the Inhibited

regeneration mode.

If not, excessive soot in the DPF may overload the

emission system and result in a reduction of

engine power.

To exit the Inhibited regeneration mode (To go
to the regeneration mode) :

1. Press down the lower side(B) of the DPF

switch(3) again for only exiting the inhibited
regeneration mode.

2. Press and hold the upper side(A) of the DPF

switch(3) for over one second to exit the
Inhibited regeneration mode and to execute the
regeneration mode.

3. When inhibited regeneration mode has been

exited, the DPF inhibited regeneration indicator
(4) will be turned off.

NOTE: If the tractor is shut off during the inhibited

mode, when restarting the tractor, the

regeneration system will return to the

regeneration mode.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды