LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 87 / 218

background image

3 - 17

⑤

Regeneration mode

▶

Fire hazard!

During the Diesel Particulate Filter(DPF) regeneration process, the exhaust stack
and fixed hood area becomes extremely hot. Park the machine outside and away
from combustible or highly flammable material.
Failure to comply could result in death or serious injury.

Warning



In this mode, the operator does not have to take

any actions, the system is activated
automatically by the engine electronic controller.

NOTE : The regeneration is the normal operating

mode.



The regeneration will be activated by ECU ;

-

When soot’s rate reaches

100% or more

.

-

When the engine is

warmed up enough.

-

When the

DPF switch is not pressed to the

Inhibited regeneration mode.

NOTE : Regeneration will be lasted for

approximately 15 to 25 minutes.

▶

If engine is turned off during the regeneration, soot will not be completely burned

and may increase fuel consumption. KEY-OFF during regeneration mode is not
recommendable because too short operation won’t finish regeneration mode, So,
we recommend to users to operate until all indicator lights are turned off without Key
switch OFF.

NOTICE

1

2



If pressing and holding the upper part of the DPF switch over 3 minutes, the regeneration can be

activated manually. In this case, if the soot’s rate is reached over minimum 30%, the regeneration
will be activated.



During the regeneration, the DPF regeneration indicator(1) and DPF temperature indicator(2) will be

turned on.



In case of turning off the engine while the regeneration is processing, the regeneration is to resume

again when restarting the engine.

«
...
85
86
87
88
89
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: Nakayama Страницы: 24

Бренд: Weir Страницы: 12

Бренд: Wacker Neuson Страницы: 11

Бренд: Daedong Страницы: 372

Бренд: Jenn-Air Страницы: 28

Бренд: Allis-Chalmers Страницы: 45

Бренд: Daedong Страницы: 262

STEINER 75-70710

Бренд: Jacobsen Страницы: 16

AERA-vator AE40L

Бренд: First Products Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды