LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 49 / 218

1 - 35

10. Location: On the left-hand side of the ROPS

frame.

- TO PREVENT SERIOUS INJURY OR DEATH;

•

Never operate a tractor without a certified

ROPS.

•

Always fasten seat belt when operating tractor

with ROPS in upright position.

•

Do not operate the tractor on steep slopes or

drop-off.

•

Avoid sharp turns at high speeds.

•

Use of ROPS and seat belt reduce the chance

of injury or death in roll-over or upset occur.

•

Do not attach ropes or chains to ROPS for

pulling purpose.

- Failure to comply could result in death or

serious injury.

- Part No. : 40234561

11. Location : On top of the right-hand fender.

(optional)

- JOYSTICK LEVER USAGE.
- TO AVOID PERSONAL INJURY; Wrong

operation causes serious injury easily.
Push the lever(1) in to lock the joystick in
neutral.

- Failure to comply could result in death or

serious injury.

- Part number : 40226388

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды