LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 147 / 218

4 - 39

Heavy parts!

▶

The ballast weights are very heavy. When removing/attaching the ballast weights,

please be careful and use a suitable hoist and specific equipment to move the
heavy parts. Failure to comply could result in death or serious injury.

Warning

②

Rear ballasting weights (optional)

- Rear wheel weights (Optional)

NOTE: Rear wheel weights are not available.

- Rear ballast weights on the 3-point
linkage



To mount the ballast weights on the rear of the
tractor, an additional weight bracket must be
installed on the rear three-point hitch.



Contact your authorized local dealer for the
bracket.



If you hard to get the bracket, you can use a
equivalent weight rear implement as the
ballasting weight.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды