LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 126 / 218

4 - 18

(5) Notices when transporting the tractor



When transporting the tractor by truck, trailer,
etc., use suitable equipment or facilities to
load or unload the tractor.



Fix the tractor tightly to the vehicle with heavy-
duty straps or chains.



When fixing the rear of the tractor, use the hitch
or hitch support.



When fixing the front of the tractor, use the
towing hook.



When driving on public roads, the transporting
vehicle must have signs and lights required by
local regulation to avoid collision with a vehicle.

▶

When fixing the tractor, do not hook or connect chains to the 4WD shaft, steering

cylinder, tie-rod or front axle. These can be damaged by the chain or excessive
strain.

▶

In case of turbocharger engine (where fitted), cover the exhaust outlet to protect

that the turbocharger does not rotate by air without lubrication.

Caution



Transport the tractor with all four wheels on a
flatbed trailer or truck. Secure the tractor as
follows:

- Secure the front of the tractor at the front
towing hook

①

of the front ballast weights or

bumper. (optional)

- Secure the rear of the tractor at the rear
drawbar or hitch

②

. (optional)

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды