LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 170 / 218

background image

5 - 22

(2) Fuel tank

①

Fuel specification and capacity :



See chapter 5-3, “Lubricants and Capacity” or

the last page in this manual.

②

Storing Fuel



If contaminants like water or dusts are mixed in

the fuel, it may cause a severe damage to the
engine. To fill the tank, the fuel storage facility
must be equipped as shown in the right figure. If
possible, fill the tank at the gas station.

④

Checking fuel level



Check the fuel gauge of the tractor fuel tank and if it’s not sufficient, fill the fuel tank with diesel fuel.

For further information about diesel fuel, see chapter 5-1-(3), 5-1-(4), 5-1-(5) in this manual.

▶

After finishing work, fill the fuel tank fully. As the temperature drops down, the

humidity in the fuel tank is condensed, and may be mixed with the fuel.

Notice

③

Using diesel for winter



General diesel fuel tends to generate paraffin

dregs in cold weather which may cause a bad
engine start. Thus, it is recommended to use
diesel for winter in cold weather.

Drum

Impurities

(3) Instrument panel & Indicators



Check if the indicators are normally turned on/off
before starting engine or while operating
frequently and periodically.



If the

engine oil pressure indicator

and

battery charging indicator

are turned on while

the engine is running, stop the engine
immediately and check the engine lubrication
system and battery charging system. If possible,
contact your authorized local dealer for check.



You must drain water in the fuel filter when the
fuel filter warning indicator lights.



For further information about indicators, refer to

the chapter 5-5, “When the warning indicator

lights” in this manual.

Battery charging

indicator

Engine oil pressure

indicator

Fuel filter

warning indicator

«
...
168
169
170
171
172
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: CID Страницы: 58

Бренд: Kalmar Страницы: 262

Бренд: Ventrac Страницы: 53

Бренд: Daedong Страницы: 246

Бренд: Cub Cadet Страницы: 52

Бренд: Mahindra Страницы: 90

Бренд: Craftsman Страницы: 76

Бренд: Montana Страницы: 26

Бренд: Broan Страницы: 10

Бренд: LS Страницы: 45

263-4WD-8G-STAGE-V

Бренд: StarTrac Страницы: 100

Бренд: Maschio Страницы: 108

Бренд: Murray Страницы: 52

Бренд: New Holland Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды