LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 177 / 218

5 - 29



Adjustment of NEUTRAL setting of
the HST control.

1. Stop tractor on a flat ground and stop the engine.

2. Lift the rear wheels of the tractor off the ground

sufficiently by using a hoist. If there is no hoist,
use a suitable device to lift the tractor safely.

For tractor weight, refer to the chapter 6,

“Dimension and Specification” in this manual.

3. Place the 4WD lever to 2WD position and apply

the wheel chock to the front wheels. It is
necessary for the tractor not to move when the
engine starts.

4. After loosening bolt(1) in half, adjust the height of

forward pedal and reverse pedal to be same by
turning shaft(2) to the left/right little by little. After
adjusting, tighten the bolt(1).

5. Start the engine after checking that HST neutral

switch is pressed by the linkage.

6. Loosen locking nut(5) and turn HST rod(6) slightly to the left or right with checking that rear axle

does not rotate anymore. Tighten the locking nut(5).

7. Check if HST neutral switch(3) is pressed or not. If the switch is not pressed, loosen bolt(4) and

adjust the position of HST neutral switch(3).

▶

When lifting the rear of the tractor, the tractor may incline to the left or right by

oscillating angle of the front axle. Insert suitable chocks between front axle and
engine frame symmetrically.

Caution

(12) Adjusting HST control linkage (HST type)



Run the engine and place the range gear shift lever in the lowest speed position.



Check if the HST tractor stops by taking off the foot from the HST pedal while driving. If the tractor
does not stop, stop the tractor by using the brake pedals. And, adjust the neutral position of the HST
as below.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды