LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 198 / 218

background image

5 - 50

(3) Battery handling and Notices

※

Battery fluid (Electrolyte) is a solution of water and sulfuric acid. It makes poisonous gas

which is very harmful to eyes, skin and clothing. And also this gas is explosive.
Read the following instructions thoroughly before handling the battery.

①

Battery check



Indicator(if fitted) on the top of the battery displays the battery state. If the indicator color is;

-

GREEN

: Normal state.

If the engine does not start despite of green color, contact your authorized dealer.

-

CLEAN

: Low charging state – charge the battery.

-

WHITE or RED

: Replace the battery with a new one after checking the vehicle.



If the terminals of battery harness are loosened, tighten it completely.

If the terminals of battery are corroded, clean it with warm water and apply grease.

Caution

▶

The gas generated from the battery is explosive. Comply with the following

instructions.
- Keep cigarettes, sparks and flames away from the battery. Use a flashlight to
check battery electrolyte level or indicator.
- Never check battery charge by placing a metal object across the terminals. Use a
voltmeter or hydrometer.
-Always remove grounded (-) battery clamp first and assemble it last. If not, it can
cause explosion by spark.

▶

Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin,

clothing and can cause blindness if splashed into the eyes.
- Never disassemble the battery.
- Do not touch the battery or liquid by bare hand without gloves or any protection.
- Flush eyes with clean water for about 20 minutes if the electrolyte is splashed into
the eyes, and get medical attention immediately.

▶

Charge the battery in an area with good ventilation and DO NOT charge a frozen

battery.

▶

Replace the old battery with a same capacity genuine product.

«
...
196
197
198
199
200
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

UpFront STS 12 Combo

Бренд: Hagie Страницы: 149

Бренд: Zetor Страницы: 197

Бренд: Sears Страницы: 27

Бренд: Iseki Страницы: 113

Бренд: McCulloch Страницы: 60

ZERO TURN 49 MOUNTING KIT

Бренд: Nordic Plow Страницы: 13

Бренд: Ventrac Страницы: 51

Бренд: Valtra Страницы: 41

Бренд: Stow Страницы: 70

Бренд: Land Pride Страницы: 26

Бренд: Ingersoll Страницы: 29

Бренд: Jenn-Air Страницы: 196

Бренд: EarthBin Страницы: 22

Бренд: Echo Страницы: 5

5400 BROCHURE 86-145

Бренд: MASSEY FERGUSON Страницы: 44

1500 BROCHURE 28-46

Бренд: MASSEY FERGUSON Страницы: 12

Бренд: MASSEY FERGUSON Страницы: 31

Бренд: MASSEY FERGUSON Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды