LS tractor MT230E 2020 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 218

LS tractor MT230E 2020 Скачать руководство пользователя страница 68

2 - 8

②

Foldable roll-bar type



The Roll-Over Protective Structure (ROPS) is
integrated and certified structure for driver’s
safety. This structure will reduce the risk of
serious injury or death when being over-turned.



DO NOT remove, modify or repair the ROPS
arbitrary. The welding, bending, drilling, grinding,
or cutting of any part of the ROPS, it can weaken
the structure.



If the ROPS is loosened or removed for any
reason, make sure that all parts reinstalled
correctly before operating the tractor.

ROPS (Roll-bar)

Warning

Roll-over hazard!

Failure to comply could result in death or serious injury.

▶

Do not modify or remove the Roll-Over Protective Structure(ROPS) arbitrarily for

safety. Unless the ROPS is applied correctly, it may cause a serious accident or
death when being overturned.

▶

Be sure to stand up the Roll-Over Protective Structure(ROPS) and check the bolts,

pins and nuts correctly kept in place.

▶

Always wear the seat belt when operating the vehicle with the ROPS in the upright

position.

▶

Do not connect chains or ropes to the ROPS for pulling purposes, as the vehicle

could tip over.

▶

When driving through door openings or under low overhead objects, make sure

there is sufficient clearance for the ROPS.

▶

In case of folding/standing the roll-over protective structure(ROPS).

- A folded ROPS does not provide roll-over protection. Do not operate the vehicle

with the ROPS folded as a standard operating mode. Do stand up the ROPS
immediately as soon as the low clearance work is finished.

- The ROPS is a heavy assembly. Be careful not to be injured by sudden folding,

which might occur when folding or standing up the ROPS by its own weight. If
possible, do cooperate with other people for the folding/standing.

- Do not wear seatbelt when the ROPS is folded down.

«
...
66
67
68
69
70
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды