LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 104 / 218

background image

3 - 34

when pushing

when pulling

(4) Remote control lever and Quick coupler (optional)



The remote control levers are used to operate the hydraulic cylinder(s) and/or motor(s) of the
implement attached to the tractor.



If you

pull

the remote control lever(s)

backward

, and the hydraulic pressure works

to the upper

couplers

of the related lever(s), and the

lower coupler(s) is

connected

to the oil tank

.



Each lever of the parallel circuit remote control valve can be operated respectively, and when
operating the levers at the same time, a quick coupler under less pressure begins to work first.



After connecting and preliminary operating the hydraulic equipment, check again the transmission
oil level of the tractor.



Depending on the remote control valve type, a set of spring-return type lever(s), detent type lever(s)
or combinations may be installed on your tractor. (optional)
-

Spring-return type

: When releasing the lever(s) after operating fully, the lever(s) will return to the

neutral position automatically.
-

Detent type

: When releasing the lever(s) after operating fully, the lever(s) is fixed on the working

position. In this case, you must move the lever to the neutral position manually after operating.

If

leaving this lever on, it may cause an over-heat and serious damage of the hydraulic system.

Lever 1

Pull

Push

Lever 2

Lever 2

Lever 1

Warning

▶

Before removing hydraulic pipes or hoses and other parts, make sure to check that

hydraulic pressure is relieved completely. The leaks of pressurized oil can cause a
fatal physical injury.

▶

Use proper personal protection equipment, before servicing the hydraulic system.

▶

Before connecting or disconnecting the hydraulic quick couplers, lower the

implements to the ground, and check that the hydraulic pressure is relieved.

Caution

▶

When connecting a high volumetric capacity cylinder to the remote control system,

lower the implement to the ground, and check if the transmission oil level is marked
between “Min” and “Max” scale on the oil gauge. If necessary, add new oil.

«
...
102
103
104
105
106
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: McCulloch Страницы: 80

Бренд: Agriweld Страницы: 11

Бренд: Belarus Страницы: 358

Бренд: Cub Cadet Страницы: 48

Бренд: Valtra Страницы: 19

Бренд: Kubota Страницы: 102

Бренд: Cub Cadet Страницы: 334

Бренд: Zetor Страницы: 140

Бренд: Yanmar Страницы: 170

Бренд: Yanmar Страницы: 239

10520 TURBO INTERCOOLER

Бренд: Zetor Страницы: 236

SPIDER 1500/14 T

Бренд: SIP Страницы: 311

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды