LS tractor MT230E 2020 Скачать руководство пользователя страница 82

Страница: 82 / 218

3 - 12

①

(5) Hazard warning light switch



This is used to warn other vehicles in case of
emergency status.



This function is integrated to the light switch for
USA market.



If turning the light switch

①

once clockwise, all

turn signal lights

②

are blinked.



When turning the light switch to “

Low beam

”

position, the hazard warning light is
automatically turned on.



Use this hazard warning light switch in
emergency situations according to your local
traffic regulation.



If the hazard warning lights are operated at the
same time when the turn signal is activated, the
hazard warning light for the opposite side of
turning direction will stop flashing and illuminate
continuously.

Light switch

▶

If using the hazard warning lights for a long time while the engine is stopped, the

battery can be discharged due to high electrical power consumption.

▶

The hazard warning lights can be turned on regardless of the key switch position.

Notice

Caution

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Бренды по названию

Популярные бренды