LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 90 / 218

3 - 20



This switch is used to enable the Engine Speed

Cruise Control(ESC) function.



If pressing the ESC main switch from position 0

to position 1 (

Off –> Ready

- ESC indicator on the instrument panel will
blink.
- Engine speed stored on ECU will be displayed
on the LCD panel.



If pressing the ESC main switch from position 1
to position 2 (

Ready –> Resume

①

(if pressing below 2 second)

– ESC

indicator will be ON and engine speed cruise
control (ESC) will begin.

②

(if pressing over 2 second)

– current engine

speed will be stored on ECU and the stored
engine speed will be displayed on LCD panel.



To exit the ESC control,
-. Press the lower side (“Off position”) of the
ESC main switch or
-. Press down the brake pedals.

(10) ESC main switch

ESC main switch

• Position 2 :

Resume

• Position 1 :

Ready

• Position 0 :

Off

ESCC indicator

LCD panel

(11) ESC speed up/down switch



This switch is used to adjust the engine speed
for ESC when the ESC is working.



If pressing the front/rear side of the switch, the
engine speed will be;

- Front side : Increased.
- Rear side : Decreased.

ESC speed up/down switch

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды