LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 122 / 218

4 - 14

▶

Modified lamps or change bulb capacity may cause a traffic accident by disturbing

approaching driver’s views.

▶

If the lamp is blown out, replace it immediately with a genuine part. In case of

driving at night, it may cause a traffic accident.

Warning

(2) Light operation

①

Headlights

②

Side lights, Front turn signal lights and Hazard

warning lights

③

Rear turn signal lights and Hazard warning

lights

④

Tail lights and Brake lights

⑤

Rear work lights (optional)

⑥

Grille work lights – Not applicable



Use the hazard warning lights and headlights
(low beam) when you are traveling on public
roads day or night. (North America only)



Do not modify the lamps or change the bulb
capacity arbitrarily.



When driving the tractor on public roads,
operate the lights according to your local traffic
regulations.



For the details about light operation, refer to

the chapter 3 in this manual.

- Roll-bar model



Your tractor is equipped with the following
lights.

▶

If using the hazard warning lights for a long time while the engine is stopped, the

battery can be discharged completely due to high electrical power consumption.

Caution

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды