LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 66 / 218

2 - 6

2-2. Safety Device

(1) Hood (Bonnet)



Hood is a protection device to prevent an
unintended access to the rotating parts around
engine; cooling fan, fan belt and rotating shaft
and pulley.



Do not remove and modify the hood.

(2) Fender



Fender is a protection device to prevent an
unintended access to the rear tires and to
prevent mud from irrupting to the driver.



Do not remove and modify the fender.

Hood (Bonnet)

Fender

(3) PTO safety cover and protection cap



PTO safety cover is a protection device to
prevent an unintended access to the PTO shaft
and to prevent an accident causing by the
rotating drive shaft.



Do not remove the PTO safety cover. If the PTO
safety cover or protection cap is damaged or
removed, replace it with a genuine part.



Do not step on the PTO safety cover.



After using the PTO shaft, apply grease and

insert the PTO shaft protection cap.

Warning

▶

If you contact the rotating shaft, it may cause a severe injury.

- DO NOT touch the rotating shaft.
- DO NOT remove the safety cover.
- Avoid loose clothes that can easily be rolled up in the rotating shaft.

PTO shaft
protection cap

PTO safety cover

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды