LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 111 / 218

4 - 3

HST type

Brake pedals

HST reverse pedal

Throttle lever

HST forward pedal

PTO switch

Key switch

1. Sit in driver’s

seat and apply
parking brake

2. Place the range gear shift lever

and HST forward/reverse pedal in

NEUTRAL

, and PTO switch in

OFF

Parking brake lever

8. Run the engine for a

few minutes to allow
engine oil and
transmission oil to warm
up.

7. Check if the battery charging

indicator and engine oil
pressure indicator are OFF
after starting engine.
If not, stop the engine
immediately and check the
problem.

3. Pull the throttle lever to

the low speed position.

6. Turn key switch to

“

START”

position. As

soon as the engine
starts, release the key
switch to “ON” position.

5. Wait until the cold start

aid indicator is OFF.
(about 10 seconds)

4. Turn key switch to “ON”

position and check if the
battery charging
indicator, engine oil
pressure indicator and
cold start aid indicator
are ON.

Caution

▶

Check each part before starting

engine.

▶

Check if there are any other

people around before starting.

▶

Place all the transmission gear

levers and switches in
NEUTRAL or “OFF” position.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды