LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 81 / 218

3 - 11

Light switch

▶

When passing with other

vehicles in the opposite lane at
night, turn the headlights to low
beam not to disturb oncoming
cars.

Caution

(4) Light switch



OFF

– Instrument panel and all lights are OFF.

– Instrument panel, sidelights and

hazard warning lights are turned on.

– Instrument panel, sidelights and

headlights (high beam) are turned on.
(use when working)

– Instrument panel, sidelights, headlights

(low beam) and hazard warning
lights are turned on. (use when driving)



Combination light switch is used to turn on/off
the following lights.

①

Instrument panel lights.

②

Hazard warning lights.

③

Side lights

④

Tail lights.

⑤

Headlights.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды