LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 130 / 218

background image

4 - 22

⑤

Handling of the 3-point linkage

①

④

③

⑤

②

⑥

⑦

Down speed control knob

Fast

Slow & lock

▶

The parts of 3-point linkage are

very heavy. When handling
them, take care not to get injury.
PLEASE BE CAREFULL !

Caution



When driving the tractor without attached implement, comply with the followings.

1. Connect upper link(5) to the fixing hook installed in front of the upper link.
2. Connect stabilizer(2) to the lower link(3) to avoid the lateral movement of the lower link.
3. Connect lower link strap to the both lower links(3) (if fitted, chain type stabilizer only)



If the 3-point linkage is not necessary, remove it as follows.

1. Remove upper link pin(7) and upper link(5).
2. Detach the rear side of the stabilizer(2) from the lower link(3) while holding the lower link tightly
not to fall down.
3. Remove lift rod (LH), lift rod (RH) and stabilizer(2) step by step.
4. Remove lower link(3) carefully not to get hurt due to its own weight.



When using hitch/drawbar, or driving on the road,
lift up the 3-point linkage and fix it by turning the
down speed control knob to the locking position.

①

Lift rod (LH)

②

Stabilizer

③

Lower link

④

Lift rod (RH)

⑤

Upper link

⑥

Lift rod pin

⑦

Upper link pin

«
...
128
129
130
131
132
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: FENDT Страницы: 51

Бренд: McCulloch Страницы: 60

Бренд: Degelman Страницы: 27

Бренд: BUG-O Страницы: 30

Бренд: CAMPAGNOLA Страницы: 4

Proxima GP Series

Бренд: Zetor Страницы: 226

'15' Series 2015 4WD

Бренд: Mahindra Страницы: 132

Бренд: CAMSO Страницы: 24

Бренд: Pasquali Страницы: 130

Бренд: FENDT Страницы: 51

Бренд: Viking Страницы: 10

Бренд: Gram Страницы: 48

Бренд: Digga Страницы: 22

Бренд: Digga Страницы: 24

Бренд: Duncan Страницы: 81

Бренд: CARRARO Страницы: 407

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды