LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 15 / 218

background image

1 - 1

◆

Safety Mark Description

- In the places where the cautions in usage are required, the marks such as “

DANGER”, “WARNING”,

“CAUTION”

are found.

- You should comply with the description marked on the decals attached on the product or the contents

marked with safety mark in this Operator's Manual.

Warning -

This indicates a potential dangerous situation that may cause a serious

injury or death if not avoided.

Caution -

This indicates a potential dangerous situation that may cause a light injury

or damage to the properties if not avoided.

Notice -

This indicates the instructions for right use for the safety of persons or

products.

Danger

- This indicates a fatal dangerous situation that may cause a serious injury

or death if not avoided.

1-1. Note to the owner – General information

▶

Illustrations in this manual may show protective shielding open or removed

to better illustrate a particular feature or adjustment.
Replace all shields before operating the tractor.
Failure to comply could result in death or serious injury.

Warning

Operator’s manual

Please have all operators read this manual carefully and keep this manual available for ready
reference. Read this manual to make sure that you have a complete understanding of how to
operate this tractor safely, correctly, and for the most effective performance of the tractor.

NOTE: This operator’s manual may be available in other languages; see your authorized local

dealer for ordering.

This manual contains important information concerning the adjustment and maintenance of your
new equipment.

NOTE: Some images of the tractor in this manual may differ slightly in some detail. Any variations

will be similar enough for you to understand the information or instructions.

Throughout this operator’s manual, references to the right-hand and left-hand sides of the tractor
are determined by facing the forward operating direction of travel.

This is the safety alert symbol. The safety alert symbol alerts you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid possible
death or injury.

1. General Notices for Safety

Notice

Caution

Warning

Danger

«
...
13
14
15
16
17
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: Valtra Страницы: 142

Бренд: Tarmo Страницы: 27

WEATHER-BRAKE 2145

Бренд: Femco Страницы: 6

Бренд: Homelite Страницы: 2

hillvert HT-RUNDLE-20

Бренд: Expondo Страницы: 7

Бренд: JOSEPH JOSEPH Страницы: 9

Бренд: Hagie Страницы: 67

Бренд: Zetor Страницы: 134

Northstar 1200UNIV

Бренд: Rankin Страницы: 32

Бренд: Verts Loisirs Страницы: 72

Бренд: DTA Страницы: 8

Бренд: Allis-Chalmers Страницы: 48

Бренд: Everything Attachments Страницы: 14

Бренд: Claas Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды