LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 175 / 218

5 - 27

Clutch pedal

Adjuster

Locking nut

Clutch rod

(10) Adjustment of Clutch pedal

play (Mechanical type)



Check the distance of the clutch pedal play.



Normal distance: 20~30mm (0.8~1.2 in.)

If the distance of the pedal play is over the
normal distance, adjust it as below.

1. Loosen the locking nut(s) and turn the adjuster

to the left/right-hand direction.

2. If the adjuster is tightened, the pedal play will be

decreased, and if loosened, it will be increased.

3. After adjusting the pedal play, tighten the locking

nut(s).

4. Check if the clutch is disengaged completely.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды