LS tractor MT230E 2020 Скачать руководство пользователя

Страница: 204 / 218

5 - 56

②

Front turn signal light bulb -

replacement

1. Remove the two screws

①

retaining the turn

signal light lens and remove the lens.

2. Push in on the turn signal light bulb

②

and

rotate bulb counter-clockwise in the socket to
remove the old bulb.

3. Insert the new bulb into the socket and turn it

clockwise until the bulb locks into place.

4. Install lenses and retaining screws.

NOTE: For about bulb specification, refer to the

chapter 5-6-(4) in this manual.

③

Side light bulb - bulb replacement

1. Remove the two screws

①

retaining the taillight

lens and remove the lens.

2. Push in on the side light bulb

②

and rotate

counter-clockwise in the socket to remove the
old bulb.

3. Insert the new bulb into the socket and turn the

bulb in a clockwise direction until tightened.

NOTE: For about bulb specification, refer to the

chapter 5-5-(4) in this manual.

NOTE: Tail light bulb

③

may be not available,

depending on the market.

Содержание MT230E 2020






















































































































































































































Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды

LS tractor MT230E 2020, Руководство оператора

Результаты поиска

Содержание MT230E 2020

Отзывы:

Похожие инструкции для MT230E 2020

Бренды по названию

Популярные бренды