LS tractor MT230E 2020 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 218

LS tractor MT230E 2020 Скачать руководство пользователя страница 160

5 - 12



For safety, the hood must be closed and
correctly latched before operating the tractor.



The hood is hinged at the rear and a gas
cylinder is attached to provide easy access to
the engine for check and maintenance.



To open the hood, push the hood opening knob
and lift the hood up.



To close the hood, pull the hood and push it
down to the locking position slightly.

▶

Before opening the hood, be sure to stop the engine completely.

▶

If opening the hood while engine is running, it can cause serious damage or death

by unintended access to the rotating shaft, pulley, V-belt, cooling fan of the engine
or engine application parts. PLEASE BE CAREFUL.

Caution



The jacking points for maintenance is depending
on serviced parts case by case. Do not hesitate
to contact your authorized dealer for asking.



Do not use the front axle assembly or steering
linkage and cylinder for jacking point. These
components have some rotating pivots and/or
does not have enough structural strength.



For general maintenance, use a flat surface
under the engine frame end or bumper for
jacking point, and additionally connect the front
towing hook to the hoist for safety.



For rear jacking points, two flat surfaces under
the rear axle housing is recommended, and
additionally use the top-link bracket and its pin
for lifting point after removing the top-link.

②

Jacking points

Rear jacking point

Rear jacking point

Top link pin

Top link

Hood opening knob

Front jacking point

Front towing hook

(7) Access for maintenance

①

Opening Hood

▶

When lifting the rear of the

tractor, apply chocks to the
slots between front axle and
engine frame symmetrically to
prevent the tractor from rolling.

Caution

«
...
158
159
160
161
162
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды