LS tractor MT230E 2020 Скачать руководство пользователя | Manualshive

Страница: 64 / 218

background image

2 - 4

warning

▶

DO NOT put your hand under the driver’s seat while sitting. It may cause a injury

by seat suspension.

▶

DO NOT adjust the seat position while driving.

(3) Seat adjustment



Before operating the tractor, adjust the position of

driver’s seat according to body size and length.



Seat F/R adjustment lever

1) After sitting on driver’s seat, lift the seat F/R

adjustment lever up to release the lock.

2) Move the driver’s seat forward or backward

according to driver’s body length.

3) Release the seat F/R adjustment lever and

ensure that seat is locked in place.



Keep the released seat belt on the seat belt rest

after working.



To prevent the driver’s seat from weathering,

raise the driver’s seat forward.

Seat F/R

adjustment lever

(4) Seat belt



Always wear the seat belt before operating the
tractor and adjust the belt to fit the operator.
1. Insert the seat belt end into the buckle until a
“click” indicates it is properly engaged.
2. To remove the seat belt from the buckle,
press the red release button on the buckle.



Check the seat belt regularly. If damaged or
frayed, replace it with a new one.

Buckle

Seat belt

Warning

▶

If not wearing the seat belt, it may cause serious injury in case of an accident.

- During operation, it must be required to wear seat belt with a cab or roll-bar
installed.
- After wearing the seat belt, adjust the belt to fit your body.

▶

If the roll-bar is folded down or removed, do not wear the seat belt.

«
...
62
63
64
65
66
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT230E 2020

Бренд: Kersten Страницы: 19

Бренд: LAMBORGHINI Страницы: 41

Бренд: LAMBORGHINI Страницы: 51

19A70054 Series

Бренд: MTD Страницы: 32

Бренд: MTD Страницы: 44

Бренд: Dong Feng Страницы: 55

Бренд: Wheel Horse Страницы: 12

Tractor TURBOMIX MTXH

Бренд: Bauer Страницы: 42

FORTERRA HSX Series

Бренд: Zetor Страницы: 222

Бренд: Toro Страницы: 2

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 20

Бренд: Toro Страницы: 20

08881 SAND PRO 5000

Бренд: Toro Страницы: 28

Бренд: Nine Stars Страницы: 2

Бренд: MRF Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды