manualshive.com logo in svg

LS tractor MT230E 2020, Руководство оператора

Поделиться
Скачать
LS tractor MT230E 2020 Скачать руководство пользователя страница 84

3 - 14

DPF switch

DOC&DPF(CCRT)

(8) DPF switch

The regeneration process is the process of 
burning and cleaning the soot accumulated in 
the DPF while driving.

This switch is used to select the 

Regeneration 

mode

or 

Inhibited regeneration mode

.

-

Regeneration mode:

If the soot is loaded over 

the designated level and the engine is warmed 
up enough, the DPF regeneration will be 
processed automatically by ECU. 

For more 

information, see page 3-17 in this manual.

-

Inhibited regeneration mode: 

The 

regeneration mode is disabled manually until 
operator inputs the signal for exiting this mode. 

For more information, see page 3-18 in this 

manual.

And, this switch is used to process the 
regeneration manually. 

For the detail operating 

methods, see page 3-17 in this manual.

①

Definitions of system components and operation

The following terms will define the system components and functional descriptions.

System component

Description

Diesel Oxidation Catalyst 
(DOC) 

This is a catalytic converter that designed specifically for diesel 
engines to reduce the emission element such as 
hydrocarbons(HC), carbon monoxide(CO), and to do 
exothermic reaction for DPF regeneration.

Diesel Particulate Filter (DPF) 

This is a filter and an after-processing component that captures 
soot in the engine exhaust gas, and to prevent the filter from 
clogging, the particulate matter will be automatically burned into 
CO

2 

at a high temperature by regeneration process.

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды