LS tractor MT230E 2020 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 218

LS tractor MT230E 2020 Скачать руководство пользователя страница 67

2 - 7

(4) Roll-Over Protective Structure (ROPS) (optional)

①

Fixed roll-bar type



The Roll-Over Protective Structure (ROPS) is
integrated and certified structure for driver’s
safety. This structure will reduce the risk of
serious injury or death when being over-turned.



DO NOT remove, modify or repair the roll-bar
arbitrary. The welding, bending, drilling, grinding,
or cutting of any part of the roll-bar, it can
weaken the protective structure.



If the roll-bar is loosened or removed for any
reason, make sure that all parts reinstalled
correctly before operating the tractor.

Warning

Roll-over hazard!

Failure to comply could result in death or serious injury.

▶

Do not modify or remove the Roll-Over Protective Structure(ROPS) arbitrarily for

safety. Unless the ROPS is applied correctly, it may cause a serious accident or
death when being overturned.

▶

Be sure to stand up the Roll-Over Protective Structure(ROPS) and check the bolts,

pins and nuts correctly kept in place.

▶

Always wear the seat belt when operating the vehicle with the ROPS in the upright

position.

▶

Do not connect chains or ropes to the ROPS for pulling purposes, as the vehicle

could tip over.

▶

When driving through door openings or under low overhead objects, make sure

there is sufficient clearance for the ROPS.

▶

In case of removing/installing the roll-over protective structure(ROPS).

- If the upper frame is removed, it does not provide any roll-over protection. Do not

operate the vehicle with the upper frame removed as a standard operating mode.
Re-install the ROPS immediately as soon as the low clearance work is finished.

- The ROPS is a heavy assembly. Be careful not to be injured by sudden folding,

which might occur when handling the ROPS by its own weight. If possible, do
cooperate with other people for the removing/installing.

- Do not wear seatbelt when the ROPS upper frame is removed.

Fixed roll-bar

«
...
65
66
67
68
69
...
»

Содержание MT230E 2020



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды