Hitachi H8S/2376 F-ZTAT Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 949

background image

Rev. 1.0, 09/01, page 137 of 904

6.4.2

Bus Specifications

The external address space bus specifications consist of five elements: bus width, number of
access states, number of program wait states, read strobe timing, and chip select (

&6

) assertion

period extension states. The bus width and number of access states for on-chip memory and
internal I/O registers are fixed, and are not affected by the bus controller.

Bus Width: A bus width of 8 or 16 bits can be selected with ABWCR. An area for which an 8-bit
bus is selected functions as an 8-bit access space, and an area for which a 16-bit bus is selected
functions as a 16-bit access space. If all areas are designated as 8-bit access space, 8-bit bus mode
is set; if any area is designated as 16-bit access space, 16-bit bus mode is set.

Number of Access States: Two or three access states can be selected with ASTCR. An area for
which 2-state access is selected functions as a 2-state access space, and an area for which 3-state
access is selected functions as a 3-state access space. With the DRAM or synchronous DRAM
interface and burst ROM interface, the number of access states may be determined without regard
to the setting of ASTCR.

When 2-state access space is designated, wait insertion is disabled. When 3-state access space is
designated, it is possible to insert program waits by means of the WTCRA and WTCRB, and
external waits by means of the

:$,7

pin.

Note: * The synchronous DRAM interface is not supported in the H8S/2378 series.

Number of Program Wait States: When 3-state access space is designated by ASTCR, the
number of program wait states to be inserted automatically is selected with WTCRA and WTCRB.
From 0 to 7 program wait states can be selected. Table 6.2 shows the bus specifications (bus
width, and number of access states and program wait states) for each basic bus interface area.

«
...
179
180
181
182
183
...
»

Содержание H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2376 F-ZTAT

Бренд: Ubiquiti Страницы: 24

Бренд: Omnia Страницы: 6

Бренд: Patton electronics Страницы: 51

Бренд: Xinje Страницы: 57

Бренд: Observint Страницы: 117

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: Ublox Страницы: 116

FireWire 800 + Hi-Speed USB Combo

Бренд: SIIG Страницы: 20

Бренд: Airlink101 Страницы: 46

Бренд: ebm-papst Страницы: 13

Бренд: FiberHome Страницы: 2

COM Express conga-TC87

Бренд: Congatec Страницы: 114

Бренд: Kontron Страницы: 32

Бренд: IBM Страницы: 168

Blend PRO BP-2002

Бренд: FOLSOM Страницы: 89

Бренд: Xilinx Страницы: 36

Бренд: Enterasys Страницы: 5

Бренд: COMBA Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды