manualshive.com logo in svg

Hitachi H8S/2376 F-ZTAT, Руководство по оборудованию

Желаете узнать больше о Hitachi H8S/2376 F-ZTAT? Скачайте бесплатное аппаратное руководство на manualshive.com прямо сейчас! Это руководство поможет вам получить подробные инструкции по использованию этого продукта. Не упустите шанс загрузить его совершенно бесплатно!

Поделиться
Скачать
background image

Rev. 1.0, 09/01, page 383 of 904

In repeat mode or block transfer mode, the CRA is divided into two parts: the upper 8 bits
(CRAH) and the lower 8 bits (CRAL). CRAH holds the number of transfers while CRAL
functions as an 8-bit transfer counter (1 to 256). CRAL is decremented by 1 every time data is
transferred, and the contents of CRAH are sent when the count reaches H'00.

9.2.6

DTC Transfer Count Register B (CRB)

CRB is a 16-bit register that designates the number of times data is to be transferred by the DTC in
block transfer mode. It functions as a 16-bit transfer counter (1 to 65,536) that is decremented by 1
every time data is transferred, and transfer ends when the count reaches H'0000.

9.2.7

DTC Enable Registers A to H (DTCERA to DTCERH)

DTCER which is comprised of seven registers, DTCERA to DTCERG, is a register that specifies
DTC activation interrupt sources. The correspondence between interrupt sources and DTCE bits is
shown in table 9.1. For DTCE bit setting, use bit manipulation instructions such as BSET and
BCLR for reading and writing. If all interrupts are masked, multiple activation sources can be set
at one time (only at the initial setting) by writing data after executing a dummy read on the
relevant register.

Bit

Bit Name

Initial Value

R/W

Description

7
6
5
4
3
2
1
0

DTCE7
DTCE6
DTCE5
DTCE4
DTCE3
DTCE2
DTCE1
DTCE0

0
0
0
0
0
0
0
0

R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W

DTC Activation Enable

Setting this bit to 1 specifies a relevant interrupt
source to a DTC activation source.

[Clearing conditions]

•

 

When the DISEL bit is 1 and the data transfer has

ended

•

 

When the specified number of transfers have

ended

These bits are not cleared when the DISEL bit is 0
and the specified number of transfers have not ended

9.2.8

DTC Vector Register (DTVECR)

DTVECR enables or disables DTC activation by software, and sets a vector number for the
software activation interrupt.

Содержание H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2376 F-ZTAT

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Бренд: D-Link Страницы: 4
DAD DSX 26 User Manual preview
DSX 26
Бренд: DAD Страницы: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Бренд: D-Link Страницы: 2
Lab.gruppen NLB 60E Operation Manual preview
NLB 60E
Бренд: Lab.gruppen Страницы: 35
Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Бренд: Magma Страницы: 2
Tripp Lite N48M Series Installation Manual preview
N48M Series
Бренд: Tripp Lite Страницы: 20
Idis DR-8432 Installation Manual preview
DR-8432
Бренд: Idis Страницы: 31
Supermicro SAS-827HD User Manual preview
SAS-827HD
Бренд: Supermicro Страницы: 16
NA DigiNet 416 User Manual preview
DigiNet 416
Бренд: NA Страницы: 22
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Бренд: Cromemco Страницы: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Бренд: Verizon Wireless Страницы: 39
Roland Super Sound Set SR-JV80-07 Owner'S Manual preview
Super Sound Set SR-JV80-07
Бренд: Roland Страницы: 8
Schrack Technik HSERG245GS Instruction Sheet preview
HSERG245GS
Бренд: Schrack Technik Страницы: 2
Eaton SONiX Pm10 Technical Manual preview
SONiX Pm10
Бренд: Eaton Страницы: 14
HighPoint RocketCache 3240X8 User Manual preview
RocketCache 3240X8
Бренд: HighPoint Страницы: 17
Nortel BayStack 660 Use Manual preview
BayStack 660
Бренд: Nortel Страницы: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Бренд: Baracoda Страницы: 16
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Бренд: Alcatel-Lucent Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды