manualshive.com logo in svg

Hitachi H8S/2376 F-ZTAT, Руководство по оборудованию

Желаете узнать больше о Hitachi H8S/2376 F-ZTAT? Скачайте бесплатное аппаратное руководство на manualshive.com прямо сейчас! Это руководство поможет вам получить подробные инструкции по использованию этого продукта. Не упустите шанс загрузить его совершенно бесплатно!

Поделиться
Скачать
background image

Rev. 1.0, 09/01, page 345 of 904

•

 

When an NMI interrupt is generated, and transfer halts

•

 

A reset

•

 

Hardware standby mode

•

 

When 0 is written to the EDA bit, and transfer halts

When transfer is halted by writing 0 to the EDA bit, the EDA bit remains at 1 during the DMA
transfer period. In block transfer mode, since a block-size transfer is carried out without
interruption, the EDA bit remains at 1 from the time 0 is written to it until the end of the current
block-size transfer.

In burst mode, transfer is halted for up to three DMA transfers following the bus cycle in which 0
is written to the EDA bit. The EDA bit remains set to 1 from the time of the 0-write until the end
of the last DMA cycle.

Writes (except to the EDA bit) are prohibited to registers of a channel for which the EDA bit is set
to 1. When changing register settings after a 0-write to the EDA bit, it is necessary to confirm that
the EDA bit has been cleared to 0.

Figure 8.12 shows the procedure for changing register settings in an operating channel.

Read EDA bit

Write 0 to EDA bit

Change register settings

EDA bit = 0?

1

2

3

4

1. Write 0 to the EDA bit in EDMDR.

2. Read the EDA bit.

3. Confirm that EDA = 0. If EDA = 1, this 

indicates that DMA transfer is in progress.

4. Write the required set values to the 

registers.

No

Yes

Changing register settings

in operating channel

Register setting

changes completed

Figure 8.12   Procedure for Changing Register Settings in Operating Channel

BEF Bit in EDMDR: In block transfer mode, the specified number of transfers (equivalent to the
block size) is performed in response to a single transfer request. To ensure that the correct number

Содержание H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2376 F-ZTAT

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Бренд: Baracoda Страницы: 42
F5 WANJet 500 Quick Start Card preview
WANJet 500
Бренд: F5 Страницы: 2
F5 ARX-500 Hardware Reference Manual preview
ARX-500
Бренд: F5 Страницы: 90
F5 ARX-4000 Parts Replacement Manual preview
ARX-4000
Бренд: F5 Страницы: 47
Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual preview
CLICK PLUS C2-02CPU
Бренд: Automationdirect.com Страницы: 10
Navitar 1-62645 Dimensional Drawing preview
1-62645
Бренд: Navitar Страницы: 1
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Бренд: ekwb Страницы: 2
Digital Voice Systems VC-20-MR2 User Manual preview
VC-20-MR2
Бренд: Digital Voice Systems Страницы: 32
Xcellon DRD-501 User Manual preview
DRD-501
Бренд: Xcellon Страницы: 24
Buffalo LinkStation 500 User Manual preview
LinkStation 500
Бренд: Buffalo Страницы: 139
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Бренд: Magewell Страницы: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Бренд: Z3 Technology Страницы: 18
Keithley 7075 Instruction Manual preview
7075
Бренд: Keithley Страницы: 108
Ebyte ECAN-W01 User Manual preview
ECAN-W01
Бренд: Ebyte Страницы: 23
Netequalizer NE3000-10 Quick Start Manual preview
NE3000-10
Бренд: Netequalizer Страницы: 14
Rane CP 52S Operator'S Manual preview
CP 52S
Бренд: Rane Страницы: 6
ATEN Altusen SN0100 Series User Manual preview
Altusen SN0100 Series
Бренд: ATEN Страницы: 178
Compaq StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem User Manual preview
StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem
Бренд: Compaq Страницы: 112

Бренды по названию

Популярные бренды

Загрузить еще бренды