manualshive.com logo in svg

Hitachi H8S/2376 F-ZTAT, Руководство по оборудованию

Желаете узнать больше о Hitachi H8S/2376 F-ZTAT? Скачайте бесплатное аппаратное руководство на manualshive.com прямо сейчас! Это руководство поможет вам получить подробные инструкции по использованию этого продукта. Не упустите шанс загрузить его совершенно бесплатно!

Поделиться
Скачать
background image

Rev. 1.0, 09/01, page 337 of 904

If a transfer request occurs in another channel during DMA transfer, the bus is temporarily
released, then transfer is performed on the channel for which the transfer request was issued. If
there is no external space bus request from another bus master, a one-cycle bus release interval is
inserted. For details on the operation when there are requests for a number of channels, see section
8.4.8, Channel Priority Order.

Figure 8.5 shows an example of the timing in cycle steal mode.

CPU

CPU

CPU

CPU

EXDMAC

EXDMAC

Bus returned temporarily to CPU

Bus cycle

Transfer conditions:

· Single address mode, normal transfer mode
· 

 low level sensing

· CPU internal bus master is operating in external space

Figure 8.5   Example of Timing in Cycle Steal Mode

Burst Mode: In burst mode, once the EXDMAC acquires the bus it continues transferring data,
without releasing the bus, until the transfer end condition is satisfied. There is no burst mode in
external request mode.

In burst mode, once transfer is started it is not interrupted even if there is a transfer request from
another channel with higher priority. When the burst mode channel finishes its transfer, it releases
the bus in the next cycle in the same way as in cycle steal mode.

When the EDA bit is cleared to 0 in EDMDR, DMA transfer is halted. However, DMA transfer is
executed for all transfer requests generated within the EXDMAC up until the EDA bit was cleared
to 0.

If a repeat area overflow interrupt is generated, the EDA bit is cleared to 0 and transfer is
terminated.

When the BGUP bit is set to 1 in EDMDR, the bus is released if a bus request is issued by another
bus master during burst transfer. If there is no bus request, burst transfer is executed even if the
BGUP bit is set to 1.

Figure 8.6 shows examples of the timing in burst mode.

Содержание H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2376 F-ZTAT

Zhone 6211 Quick Installation Instructions preview
6211
Бренд: Zhone Страницы: 1
ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Бренд: ebm-papst Страницы: 16
LORD AP5103 Series Technical Manual preview
AP5103 Series
Бренд: LORD Страницы: 9
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Бренд: Delta Страницы: 2
Alacritech 1000x1 Hardware Installation Manual preview
1000x1
Бренд: Alacritech Страницы: 20
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Бренд: LSI Страницы: 3
Z-Wave RAZBERRY 7 PRO Quick Start Manual preview
RAZBERRY 7 PRO
Бренд: Z-Wave Страницы: 6
Qlogic Storage Networking (Unified Fabric Pilot) Installation Manual preview
Storage Networking (Unified Fabric Pilot)
Бренд: Qlogic Страницы: 76
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Бренд: Dahua Страницы: 33
HighPoint SSD7540L Quick Installation Manual preview
SSD7540L
Бренд: HighPoint Страницы: 10
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Бренд: Trend Micro Страницы: 3
Advantech 3718HG User Manual preview
3718HG
Бренд: Advantech Страницы: 68
Dataprobe iBoot Instruction Manual preview
iBoot
Бренд: Dataprobe Страницы: 16
ZiLOG Z8 GP ZGP323 User Manual preview
Z8 GP ZGP323
Бренд: ZiLOG Страницы: 11
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Бренд: Nvidia Страницы: 160
Black Box Secure Site Manager 16 Quick Start Manual preview
Secure Site Manager 16
Бренд: Black Box Страницы: 16
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Бренд: ADLINK Technology Страницы: 48
Lanner ECA-4027 User Manual preview
ECA-4027
Бренд: Lanner Страницы: 99

Бренды по названию

Популярные бренды

Загрузить еще бренды