Graco SuperCat 232721 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 114

background image

308925

94

Service

Power Supply Turbine Alternator Service

NOTE:

Replace turbine bearings after 2000 hours of

operation. Part No. 223688 Turbine Alternator Repair
Kit is available.

1.

Follow the

Pressure Relief Procedure

on page 21.

2.

Turn off the air to the control.

3.

Open the access door (125). See Fig. 106.

4.

See the parts drawing on page 103 for the location
of the power supply.

5.

Disconnect the electrical connector (118b) from the
wire harness.

6.

Remove the two screws (103) and remove the
power supply (118) from the control.

7.

Remove the six screws (118f) and carefully sepa-
rate the power supply housings (a., b.). See Fig.
115.

8.

Disconnect the 3-wire connector (c.) from the
circuit board (118c).

9.

Carefully pull the alternator (118g) out of the
housing (a.).

10. Use an ohmmeter to test the turbine alternator coil.

Measure the resistance between the two outer
terminals of the 3-wire connector (c.). The resist-
ance should be 3 to 5 ohms. If the reading varies
from this value, replace the alternator.

11. Measure the resistance between each outer

terminal of the 3-wire connector and the turbine
alternator housing. The resistance should be
infinite. If the resistance is not infinite, replace the
alternator.

12. Inspect the gasket (118a) and replace if damaged

or worn.

13. Push the alternator (118g) into the housing (a.).

14. Connect the 3-wire connector (c.) to the circuit

board (118c).

15. Assemble the power supply housings (a., b.) and

secure them with the screws (118f).

16. Secure the power supply (118) to the control with

the screws (103).

17. Connect the electrical connector (118b) to the wire

harness.

18. Close the access door (125). See Fig. 106.

Fig. 115

TI0741A

118p

118a 118g

118c

118k

118b

118f

118n

118d

1

Set the air regulator to 25–30 psi
(0.17–0.2 MPa, 1.7–2.1 bar).

118l

118m

118e

a.

NOTE:

Exploded assembly orientation

reversed to clearly see parts.

c.

b.

«
...
92
93
94
95
96
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Бренд: Rangevision Страницы: 28

Бренд: natus Страницы: 20

Dantec Keypoint G4

Бренд: natus Страницы: 42

Бренд: natus Страницы: 149

Бренд: Accurate Technology Страницы: 10

Бренд: Gage Bilt Страницы: 28

Бренд: mychway Страницы: 56

Zen-O lite RS-00600

Бренд: GCE Страницы: 20

Бренд: Garrick Страницы: 8

Бренд: S&C Страницы: 32

CareTips Provox FreeHands FlexiVoice

Бренд: Atos Medical Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды